Jul 04, 2024

What is plastic extrusion lines?

Leave a message

 

Worldwide, extrusion lines successfully process more plastics into products than other processes by consuming at least 36 wt% of all plastics. It contains up-stream to down-stream equipment.

 

Working principle

 

An extruder is a combination of screw conveyor and compressor. As a conveyor, it mechanical acts as 'screwing' itself backward. Since the screw itself stays in one place, the plastic does the moving and is forced out
through the die. The essential parameter in the extruder's pumping process is the interaction between the rotating flights of the screw and the stationary barrel wall. For the plastic materia! to be conveyed, its friction must be low at the screw surface but high at the barrel wall. If this basic criterion is not met, the plastic will probably rotate with the screw and not move output direction

 

Core composition

 

This structure contain
(1) drive motor (from 20-2000 hp infinitely variable speed drives directly coupled to reducer for maximum efficiency all deigned to save floor space); 
(2) high efficiency gears to process all plastics (heavy duty, heat treated helical or herringbone gears equipped with shaft-driven oil pumps and oil cooler);
(3)long-lasting thrust bearing (with life expectancy well in excess of 30 years'continuous operation);
(4) large round standard feed opening.
(5)Vacuum exhaust system.
(6)heating and cooling. There are many different extruder types that have been designed (some patented) for over a century to produce the wide variety of plastics and products. The widely used are the single-screw extruders and twin-screw extrud-Ers.

 

Plastic Processes

 

PVC ,PC ,PS ,PET ,PE ,PP sheet, roofing tile, production line.
WPC ,SPC Flooring Sheet Extrusion Line ,plastic profile extrusion line
Wood plastic production line, various types of granular materials, powder, various new plastic products, products are exported to Europe, the Middle East, Africa and South Asia and other countries, all above product projects Are dedicated to the terminal customers, for customers to provide a complete set of key solutions for projects.

 

Maintenance

 

As a general statement, it can be stated that periodic checkups and regular maintenance should become a habit (at least using your maintenance manuals from the equipment supplier).

Include factors such as:

(1) watch out for plastic, water, and oil leaks;

(2) change oil in gear box and transmission (if oil-driven) at least every six months if operating on one shift or three to four months if operating on more shifts;

(3) lubricate required parts;

(4) check band heaters (for tightness), thermocouples, pressure transducers, etc.;

(5) check control circuits (electrical, hydraulic, mechanical, etc.);

(6) check die opening with a device such as a feeler gauge;

(7) routinely check the line for alignment, level, and parallelism, particularly windup equipment;

(8) keep all rolls clean and rust-free;

(9) check safety devices on all equipment;

(10) keep shop clean;

(11) keep spare parts in stock based on experience and/or suppliers;

(12) set up sessions for personnel to 'repeat' instructions on safety equipment procedures and prevent hazards harmful to personnel, equipment, and product; and others.

(13)Know the signs of trouble, such as unusual noise, before they occur.

It is important to set up preventive maintenance procedures on all equipment. Equipment is built to operate if properly maintenance is used. Processors should make it a habit to perform regular checkups and maintenance work based on equipment suppliers' recommendations and one's practical experience

 

Cost

 

The extruder and its components (gear pump, die, etc.) are costly. However, the other equipment in the line is usually more expensive and
even a single piece of equipment can be more costly. As an example, up to one-third of the capital equipment cost in a film line goes for the winder [2901. Major costs may be incurred at the end of the extrusion line, on finishing, trimming, postforming, and very important the windup or stacking equipment. Sophisticated materials handling equipment becomes costly. Nevertheless, although these costs are high, there is normally a good return on investment provided you (or some one you trust) know what is required In a production line that has a relatively long run, the cost of equipment includes its financial amortization, and could be about 5%.Plastic material cost could be as high 80% for high volume production. The other costs include power, water, labor, overhead and taxes. With precision, shortrun costs could be equipment at 20-30%, and materials at 45-50%. So, as it is usually stated, do not buy equipment just because it cost less, since more profit can occur with the more expensive equipment. Of course, the reverse is possibly true. So, buyer has to know what is wanted when ordering. A line with 1000-40001b/h output would cost $0.5-1 million.

 

Send Inquiry